Two houses on the same street, both repainted the same summer with the same product. One looks right at year nine. The other started peeling at year four.
Usually the difference is not the paint and not the crew. It is the siding. Substrate decides how much prep the job needs, which primer is correct, how much caulk goes on, and what the realistic lifespan actually is. A bid that does not name your siding material has not accounted for any of that.
Here is what changes, material by material, on exterior painting work across King and Snohomish County.
Cedar and Other Real Wood
Still the most common siding on Western Washington homes, and the most demanding.
Wood moves. It takes on moisture in winter and gives it up in summer, and the paint film has to stretch and relax through every cycle without cracking. That is why 100 percent acrylic matters more on cedar than on anything else: it stays flexible where a cheaper resin goes brittle and lets go.
What cedar needs that others don’t:
Cedar contains natural tannins that bleed through finish coats as brown or rust-coloured staining, especially around knots and anywhere bare wood is exposed. A latex primer will not block them. Bare or newly exposed cedar needs a stain-blocking primer, and skipping it is the single most common reason a white house turns blotchy in its first wet season.
Cedar also checks. Those fine splits along the grain open with age, and each one is a path for water to get behind the film. They get filled, not painted over.
Realistic lifespan: seven to ten years with full prep. Four to five if prep was cut, because on wood the prep is the job.
South and west elevations in open sun in Marysville or Lake Stevens will show UV wear before the shaded sides do. North elevations will grow moss instead. Both run out at roughly the same time, for different reasons.
James Hardie and Other Fiber Cement
The easiest of the four to repaint, and the one most often overpriced because painters quote it like wood.
Fiber cement is dimensionally stable. It barely moves with moisture, so the film is not being flexed to death, and it does not rot, check or bleed tannin. Prep is genuinely lighter: wash, scrape any failed areas, caulk, prime bare spots, two coats.
What still matters:
The joints and the cut ends. Hardie is almost always factory-sealed on the face and raw on the cut edge, and installers cut on site. Every field cut, every butt joint, every penetration is a raw edge drinking water unless it is primed and caulked. On a wall that looks perfect this is invisible, and it is where fiber cement jobs fail.
Factory-finished Hardie with a ColorPlus coating is a separate conversation. It is a baked finish with its own warranty, and painting over it voids that. It also needs a specific prep approach, because the factory coating is smooth and tight and does not accept a new film without proper adhesion work. Worth confirming which you have before anyone quotes it.
Realistic lifespan: ten to fifteen years. The longest of the four, which is most of why people choose it.
LP SmartSide and Engineered Wood
This one catches people out, because it looks like wood and behaves like neither wood nor fiber cement.
Engineered wood products are wood strands and resin, factory-coated. The coating is the waterproofing. Once it is compromised the core is exposed, and engineered wood swells irreversibly when it gets wet. There is no sanding that back.
What LP needs:
Primer compatibility, specifically. Not all primers bond to the factory coating, and the wrong one delaminates in sheets within a couple of seasons. The painter should be able to tell you the product by name, not say “we use a good primer.”
Cut edges again, and harder than Hardie. Field-cut LP must be sealed. An unsealed bottom edge above a splash zone is the classic failure: the board swells, the seam opens, and the repair is a replaced board rather than a touch-up.
Realistic lifespan: eight to twelve years, assuming the factory coating was intact at repaint and the edges got sealed.
T1-11 and Plywood Panel Siding
Common on 1970s and 1980s homes around Everett and Snohomish, and the material most likely to be at end of life rather than due for paint.
T1-11 is plywood, and plywood delaminates. Once the face veneer starts separating, paint bridges the gap for a season and then fails along the same line. The grooves hold water, the bottom edge wicks it up, and panel edges at joints are usually the first to go soft.
The honest assessment on T1-11 is often that painting is the wrong spend. We would rather tell you that at the estimate than take the job and watch it fail.
Where the panels are sound, it paints well and holds six to eight years. The judgment call is whether they are sound, and that is a screwdriver-and-thumb test on the bottom edge and around every penetration, not a look from the driveway.
Vinyl and Stucco, Briefly
Vinyl can be painted, with two hard rules. The new colour must be the same value or lighter than the old, because dark paint on vinyl absorbs heat the panel was not engineered for and it will warp. And it needs a vinyl-safe acrylic that moves with the substrate, since vinyl expands and contracts more than anything else on this list.
Stucco and EIFS need a breathable coating. Stucco holds moisture and has to release it outward; seal it with the wrong product and the water goes into the wall assembly instead. Hairline cracks get elastomeric filler. This is a different trade discipline from siding, and worth confirming your painter does it regularly.
Side by Side
| Siding | Prep weight | Critical detail | Lifespan |
|---|---|---|---|
| Cedar / real wood | Heaviest | Stain-blocking primer, filled checks | 7–10 yrs |
| Fiber cement (Hardie) | Lightest | Primed and caulked cut edges | 10–15 yrs |
| LP SmartSide | Moderate | Compatible primer, sealed field cuts | 8–12 yrs |
| T1-11 / plywood | Moderate to heavy | Delamination check first | 6–8 yrs |
| Vinyl | Light | Same-or-lighter colour, vinyl-safe paint | 8–10 yrs |
| Stucco / EIFS | Moderate | Breathable system, elastomeric crack fill | 8–12 yrs |
What to Ask a Bidder
Three questions, and the answers tell you whether the bid is built from your house or from a template.
What is my siding, and what primer are you using on it? A specific product name per substrate. “Premium primer” is not an answer on cedar or LP.
How are you handling cut edges and field cuts? The correct answer mentions them without prompting on Hardie and LP. If this is the first time it has come up, it is not in the price.
What did you find on the bottom edges? Any bidder who has walked the house has looked there, because that is where every one of these materials fails first.
Mixed-material homes are common here, especially on remodels and additions, and they need the right system on each surface rather than one product everywhere. That is a line item worth seeing broken out.
Timing Is the Same Whatever the Material
Late May through early October, surface temperatures above 50°F, and a dry window after application. Substrate changes the prep, not the weather. Our guide to how long exterior paint lasts here covers the climate side, and exterior maintenance between repaints covers the annual routine that adds years to any of these.
If you have wood siding, you likely have a wood deck or fence on a much shorter cycle. Deck and fence staining runs every two to three years, and doing it in the same mobilisation costs less than two visits.
Get a free exterior painting estimate or call (206) 930-8885. We serve Everett, Marysville, Lake Stevens, Snohomish, Mukilteo, Edmonds and 23 cities across Snohomish and King County.
